Restore degraded concrete without sagging, even on vertical surfaces and overhead.

Helical bar in stainless steel Kimisteel INOX X-BAR Kimia
Key features
- ModelKimisteel INOX X-BAR
- LineKimisteel
- RegulationsEN 845-1 EN 10002-1 EN 846-5 EN 846-7
- Made in Italy100% Italian production
- Certified CVT systemMinisterial Technical Assessment Certificate no. 207
- DurabilityFinal degradation rate 0.4% (maximum permitted limit 20%)
What it is
Helical bar in stainless steel Kimisteel INOX X-BAR Kimia. Key specifications: model Kimisteel INOX X-BAR, line Kimisteel, regulations EN 845-1 EN 10002-1 EN 846-5 EN 846-7.
FRP and FRCM structural strengthening is a system of fibre fabrics, meshes and connectors, applied with resins or mortars, that increases the strength of beams, columns and masonry.
What it is for
Used for strengthening masonry and concrete structures and for structural fixings, where the fixing is load-bearing and must be calculated.
How to use it
Strengthening must be carried out to a design by a qualified engineer. Remove render and deteriorated material, repair the substrate and apply the primer; then apply the first coat of resin or mortar, lay the fabric or mesh taut and free of air bubbles and cover it with the second coat. Insert the connectors into clean holes filled with resin; handle resins and primers with gloves and safety glasses.
Where it is used
- Industrial construction
- Conservation and restoration
- Renovation
Technical data
- Model: Kimisteel INOX X-BAR
- Line: Kimisteel
- Regulations: EN 845-1 EN 10002-1 EN 846-5 EN 846-7
- Made in Italy: 100% Italian production
- Certified CVT system: Ministerial Technical Assessment Certificate no. 207
- Durability: Final degradation rate 0.4% (maximum permitted limit 20%)
- Use in cultural heritage: Over 12 km installed in the Papal Basilica of Santa Maria degli Angeli in Assisi
- Steel used: AISI 304 / AISI 316
- Appearance: Helical bars
- Length (cm): 100 - 1000
- Nominal diameter (mm): 6
- Nominal bar area (mm²): 7,4
- Tensile breaking load (kN): 8,60
- Tensile breaking strength (N/mm²): 1165
Who it is for
Designed for bricklayers and restorers.
Related products
- Carbon reinforcement bars Kimitech Tondo CB Kimia
- Preformed glass fibre corner bead Kimitech Corner CRM 33x33, 66x66, 99x99 Kimia
- Fibre-reinforced thixotropic cement mortar Betonfix FB Kimia — from the category Fibre-Reinforced Thixotropic Cement Mortars
- Rigid rubber mortar-spreading trowel, single edge, 4200, Pavan — from the category Trowels, Spatulas and Floats
- Two-part thixotropic styrene-free polyester resin Kimitech F3 Kimia — from the category Chemical Anchors
- Browse the whole category: FRP and FRCM Structural Strengthening Systems
Before you order
In your request, please state the length, the diameter, the supply voltage and the quantities required, so we can give you the right quotation first time.
For prices and availability, request a quote from AMES Srl: we will reply with our quotation, delivery times and, where needed, an equivalent technical alternative.
Specifications 25
| Model | Kimisteel INOX X-BAR |
|---|---|
| Line | Kimisteel |
| Regulations | EN 845-1 EN 10002-1 EN 846-5 EN 846-7 |
| Made in Italy | 100% Italian production |
| Certified CVT system | Ministerial Technical Assessment Certificate no. 207 |
| Durability | Final degradation rate 0.4% (maximum permitted limit 20%) |
| Use in cultural heritage | Over 12 km installed in the Papal Basilica of Santa Maria degli Angeli in Assisi |
| Steel used | AISI 304 / AISI 316 |
| Appearance | Helical bars |
| Length (cm) | 100 - 1000 |
| Nominal diameter (mm) | 6 |
| Nominal bar area (mm²) | 7,4 |
| Tensile breaking load (kN) | 8,60 |
| Tensile breaking strength (N/mm²) | 1165 |
| Shear breaking load (kN) | 5,1 |
| Yield strength (N/mm²) | 957 |
| Bar shear strength (MPa) | 685,1 |
| Bar elongation at break (mm) | 2,5 |
| Elastic modulus, GPa | 107 |
| Pull-out test results | Tensile load |
| Brick 10 N/mm2 400 kg/m3 EN | 771-1] |
| Mortar 27 N/mm2 EN 9982 | 1000 N |
| Bars inserted at right angles to the substrate | PULL-THROUGH TEST RESULTS* |
| Tensile load | Nominal diameter [mm] |
| Bars angled at 45° to the substrate | KIMISTEEL INOX X-BAR |
The perfect setup for this job
Everything you need in one place, from functionality to safety.
For the job
Anchor the fabrics, bars and meshes of structural strengthening systems to the substrate.
Cut stone, concrete and brick when fitted to an angle grinder or site machines.
Drill concrete, masonry and stone by combining rotation and hammer action.




